40U Anti-Rust Paint Outdoor Equipment Enclosure Climate Controlled Cabinet

Quick Details:

Payment & Shipping Terms:

1. Specifications

(1) Technical Parameters

(2)Accessories List

Dimension Diagram

Cabinet External Dimension (W×D×H):1000×1000×1800mm (excluding air conditioner and pole)

2. Application Scope

The ET100100180 Outdoor Base Station Cabinet is mainly used in communication base station, such as 4G system, communication/network integrated service, access/transmission switching station, emergency communication/transmission, etc.

3. Cabinet Introduction

3.1 Cabinet Material

The cabinet is made of galvanized steel, with double walls, thickness of outer plate: 1.5mm, thickness of inner plate: 0.8mm. There are heat insulation between inner wall and outer wall. The insulation material is 40mm PEF. The cabinet is assembled type.

3.2 Cabinet Structure

The cabinet includes two compartments, with separated upper compartment and lower compartment. The upper compartment is equipment compartment, including 19” rack, 30U space. The lower compartment is for managing cables.

3.3 Cabinet Door and Lock

The cabinet door uses embedded structure. The door opening angle is larger than 110°and the door limit device can limit the opening angle. The lock is theftproof three point lock, supporting padlock.

4. Main Electrical Components

LED illumination lamp are on top of the cabinet.

5. Wire Routing Design

5.1 Feeder cable and other external cables all use bottom wiring method.

5.2 Users can put cables from the top of the pole. After going through the pole, cables will enter the cabinet through the bottom cable entrance hole.

6. Grounding Protection

• The cabinet includes grounding copper bar with anti-corrosion coating, with 120mm² sectional area. There are enough screws for wiring connection terminals.
• The metal part of the cabinet should be interconnected and be connected with grounding bar. Connection resistance between any two points is lower than 0.1Ω.
• Protective earthing of other equipments inside the cabinet should be connected to the grounding bar.

7. Theft Proof Design

7.1 Door lock theft proof design

• Damage resistance of the theft proof lock meets GA/T 73-1994 “Mechanical Anti-theft Lock” class B requirement, supporting padlock.

• Three point lock

7.2 Connection and Fastening

• Use anti-loose threaded connection as structure and bearer connection. Anchor bolt for fixing cabinet use hot dip galvanized bolts.
• Door hinges use inner hinge mode.

7.3 Appearance and Surface Treatment

Cabinet surface coating is outdoor special powder coating, with white gray color (PANTONE 428C). The coating complies with GB/T 3181-2008 requirement.

8. Features

8.1 The cabinet is dustproof, sunproof and rainproof, which is used in outdoor environment.

8.2 The cabinet cooling use two air conditioners, which work in alternation to continuously keep thermostatic inside the cabinet.

8.3 The layout of the cabinet is reasonable, which will facilitate cable access, fixing and grounding. At the bottom of the cabinet, there are entrance holes individually for power cable, signal cable and optical cable.

8.4 All the cables, sealing and heat insulation used in the cabinet are made from flame retardant materials.

8.5 The cabinet uses assembled structure, easy for installation.

8.6 The cabinet includes 19” standard installation rack.

8.7 The cabinet includes stainless steel pole, for user to installing antenna.

9. Technical Specs

• Applicable environment conditions:

Environment temperature: -40°C ~ + 70°C

Environment humidity (RH): ≤95% (at + 40°C)

Air pressure: 62kPa ~ 102kPa

• Material: quality galvanized steel
• Surface treatment: degreasing, derusting, rustproof phosphating (or galvanizing), powder coated.
• Cabinet load bearing: ≥600kg
• Ingress protection: IP55
• Flame retardance: comply with GB5169.7 test A
• Insulation resistance: the insulation resistance between grounding devices and cabinet body parts is not lower than 2X104M/500V(DC).
• Withstand voltage: the withstand voltage between grounding devices and cabinet body parts is not lower than 3000V(DC)/1min.
• Mechanical strength: each surface can bear upright pressure＞980N; after the door is open, its outer end can bear upright pressure ＞200N.

10. Cabinet Installation

10.1 Position of installation hole at cabinet base is as the following diagram.

Diagram 1

10.2 Users prefabricate concrete base.

10.3 Pre-embed 4pcs M10×100 anchor bolts on the concrete base. Distance between bolts are as that in diagram 1, with 40mm bolt exposed height. Put the cabinet on the concrete base, align anchor bolts, then screw on nuts, and tighten them with wrench.

10.4 According to site situation, put the cabinet on the concrete base with forklift, crane or manually, and fix it on the concrete base with bolts.

11. Packing and Shipping

Our Delivery Agent

The goods can be shipped by sea, by air, by courier, by land, by train, etc.

Besides the following delivery agent, we can also look for the delivery agent with the best price in china if you need us to do for you.

12. Our Contact Information

Mobile Phone: 0086-13752765943

Telephone: 0086-0755 66600941

Email: info@estel.com.cn

lxf.estel@hotmail.com
Skype: fiona.liang10

Introduction 

Tianjin Estel Electronic Science and Technology Co., Ltd (ESTEL(GUANGDONG)TECHNOLOGY CO., LTD), located in China, is a professional supplier of integrated outdoor telecom cabinet and temperature control solutions for outdoor telecom base station. As a science and technology innovative company, we engage in the R&D, manufacture, and sales of telecommunication equipment. Estel has a well-established team of technical and management experts who can meet customers’ specific needs accurately.

The base station integrated solutions and products include outdoor integrated telecom equipment cabinet, battery cabinet, RRU cabinet, power supply cabinet, environment monitoring system, TEC peltier air conditioner, AC220V compressor air conditioner, DC48V variable frequency air conditioner, heat exchanger, rectifier, UPS, embedded telecom power system etc. All the above solutions and products can be custom made.

Our products and solutions have been deployed all over China. Our main domestic customers are China Telecom, China Mobile, China Unicom, State Grid, Shenzhen / Beijing Metro and Huawei / ZTE etc. In addition, our products have been exported to Europe, North America, South America, Central America, Southeast Asia, Africa, Australia, Mid East countries, etc.

“ Customers First, Quality First ” is always our principle. We have attained many certifications, such as ISO9001, ISO14001, OHSAS18001, CE, UL, FCC etc. AS a telecom integrated solutions / energy saving system integrator in China, We have strong advantages in technology competitiveness, management competitiveness ,service competitiveness and price competitiveness. Through many years of experiences in design, production and implementation of different projects around the world, we have gained great reputation. Relying on professional technique and strict quality control, we will continuously offer high cost-effective products and solutions to our respectable customers globally. We will always try our best to meet customers’ need and requirement.

Company Capability

Trade & Market